Why Does Cylinder 4 Keep Misfiring? Possible Causes and Diagnostic Checks

By | November 21, 2026

Why Does Cylinder 4 Keep Misfiring? Possible Causes and Diagnostic Checks

A recurring cylinder 4 misfire can have several causes, so the cylinder number alone does not identify a failed part. The available diagnostic discussion raises ignition faults, low compression and valvetrain problems as possible leads. The cause should be confirmed on the individual vehicle before parts are replaced.

Why does cylinder 4 keep misfiring?

A cylinder-specific misfire may involve the spark plug, its boot or the ignition coil, but it can also have a mechanical cause. In the diagnostic discussion, a burn hole or pinhole in a spark-plug boot was identified in one case as a possible route for the spark to arc incorrectly. Contributors also recommended inspecting the plug and, where the vehicle design permits, moving the coil to another cylinder to see whether the misfire follows it.

Other observations in the discussion included inconsistent ignition activity on cylinder 4, a low relative-compression result, and possible camshaft or lifter wear. A dropped valve seat was mentioned in a separate case. These are examples from individual investigations, not proof that any one of them is responsible for every cylinder 4 misfire. One contributor also described a coil-driver fault on a similar vehicle, making the driver or its control circuit a possibility to investigate when test evidence points that way—not a default explanation.

The source is a diagnostic discussion involving particular vehicles and case histories. It is not a prevalence study or a manufacturer workshop manual, and it does not provide vehicle-specific pinouts, limits or repair procedures. You can read the original cylinder 4 misfire diagnostic discussion for the reported observations.

What should be checked next?

A sensible diagnostic sequence is to confirm the affected cylinder, inspect the accessible ignition components, and then move to electrical and mechanical testing if the fault remains:

  1. Verify which cylinder is misfiring. A technician can use scan-tool misfire data or the relevant misfire PID to establish whether the fault is isolated to cylinder 4. A stored cylinder indication identifies where misfires are being detected; it does not, by itself, identify the cause.
  2. Inspect the cylinder 4 spark plug and boot. Check for visible deterioration or damage, including a burn hole or pinhole in the boot, and assess the spark plug condition. The discussion describes a boot fault found in one case, but a visual inspection alone may not settle every diagnosis.
  3. Compare the ignition coil where appropriate. If the vehicle’s design and service procedure allow it, a technician may move the coil to another cylinder and check whether the misfire moves with it. If the fault follows the coil, that is useful evidence. If it remains on cylinder 4, the result points away from the coil but does not identify the remaining cause on its own.
  4. Investigate ignition signals and compression if the fault remains. The discussion reports inconsistent ignition-voltage observations and a relative-compression test. Interpreting ignition waveforms requires suitable equipment and experience. In the reported case, the oscilloscope sample rate was considered too slow to capture the ignition event adequately, illustrating why waveform results need careful interpretation. The discussion does not provide a complete test method or vehicle-specific specifications.
  5. Follow up mechanical evidence. A low compression result, or evidence suggesting a camshaft, lifter or valve-seat problem, calls for further mechanical diagnosis rather than repeated replacement of ignition parts. A qualified technician can determine which additional checks are suitable for the particular engine.

Do not treat the cylinder number as a parts diagnosis

A misfire PID, a damaged-looking boot, an unusual ignition waveform or a low compression result is evidence that guides diagnosis; none necessarily confirms a single failed component. The discussion itself raises both ignition and mechanical possibilities in the same investigation. The most useful approach is to test each credible lead rather than replacing parts solely because cylinder 4 is named.

Coil-driver or control-module investigation is generally a later possibility when the test results support it. It should not be assumed simply because plugs or coils have already been replaced. Follow the vehicle maker’s service information for testing and component removal. If access is difficult, specialist equipment is required, or you are uncertain about the work, use a qualified technician. Do not attempt loaded-engine tests, such as power-braking, on the basis of the diagnostic discussion.

Further reading

For wider background on ignition, compression and valvetrain causes, see our broader guide to cylinder misfire causes. The supplied evidence does not establish whether a particular vehicle is safe to drive with this fault; for a separate discussion of that subject, read our guide to cylinder 4 misfire driving concerns.


Continue Reading

You may also be interested in: Renault Kadjar 1.6 DCI Engine Mount R9M: Diagnosis, Safety Checks, and Professional Follow-Up

Leave a Reply

Your email address will not be published. Required fields are marked *