2010 Honda Accord Oil Filter: Part Numbers, Fitment, and Replacement

The right 2010 Honda Accord oil filter depends on the engine and the catalogue application you are using. For the 2.4-litre LX-S listing, an OEM Honda filter is 15400-PLM-A02. Major parts catalogues also list spin-on alternatives, including Mobil 1 M1-110A and Fram PH7317. Confirm the filter against your registration, VIN, or engine before buying, particularly if your Accord is not the 2.4-litre LX-S application.

What Oil Filter Is Needed for a 2010 Honda Accord?

A spin-on oil filter is typically used. AutoZone’s 2010 Accord catalogue identifies the Mobil 1 M1-110A and Fram PH7317 as compatible examples, but its wording is general rather than engine-specific. Check the retailer’s vehicle selector carefully before ordering a 2010 Accord oil filter.

This matters because catalogue listings can vary by engine, trim, and market. A filter that looks similar, or has a similar thread size, is not automatically the correct application. The sealing-gasket diameter, bypass-valve design, and overall filter dimensions also need to match the engine’s requirements.

Honda Oil Filter Part Number 15400-PLM-A02

15400-PLM-A02 is the OEM Honda oil-filter number shown for the 2010 Accord LX-S with the 2.4-litre four-cylinder engine in the supplied Honda parts catalogue. That catalogue describes it as an OEM filter and lists fitment across selected Honda vehicles, so it should not be treated as a blanket part number for every Honda or every Accord engine without a fitment check.

You can view the application in the 2010 Honda Accord LX-S 2.4L OEM filter catalogue. If you own a V6 Accord, use your VIN or the retailer’s engine-specific lookup rather than relying on a four-cylinder listing.

2010 Honda Accord Oil Filter Size and Aftermarket Fitment

There is more to oil-filter size than the diameter of the canister. Listings should be matched by application, because the thread, gasket, pressure-control features, and physical clearance all matter. For that reason, the most reliable approach is to use a catalogue lookup for the exact 2010 Accord engine, then compare the part number on the box with the approved listing.

If you prefer Fram, use the manufacturer’s 2010 Honda Accord oil-filter finder to verify the application. The Fram PH7317 is one aftermarket number identified by AutoZone for the 2010 Accord, but a live fitment check remains sensible before purchase.

Where Is the Oil Filter in a 2010 Honda Accord?

The oil filter is a spin-on service part mounted on the engine, rather than an insert located in an airbox-style housing. Its exact access point can differ with the engine, so do not assume that photos or instructions for a four-cylinder Accord apply to a V6.

For a DIY oil change, identify the filter from underneath only after the vehicle is safely supported on suitable stands or ramps on level ground. Do not work beneath a vehicle supported solely by a jack. If access is unclear, consult the correct service information for your engine or have a workshop point it out before loosening any component.

2010 Honda Accord Oil Filter Replacement: What to Check

Replacing the filter is normally done during an engine-oil change. Have the correct new filter, the specified engine oil, a drain pan, and appropriate tools ready. Allow the engine to cool enough to avoid burns, and keep oil away from belts, exhaust parts, and the ground.

1. Verify the filter part number against the engine or VIN before opening the packaging.
2. Drain the old oil safely, following the correct vehicle procedure.
3. Remove the old filter and make sure its rubber sealing gasket has not remained stuck to the engine.
4. Fit the new filter in accordance with the filter and vehicle instructions; do not guess at tightening specifications.
5. Refill with the correct oil, check for leaks after starting, and recheck the oil level as directed by the vehicle information.

A doubled gasket is one of the avoidable mistakes in a filter change: if the old gasket stays on the engine and the new filter is installed over it, oil can leak badly. Stop the engine immediately if you see a significant leak or the oil-pressure warning light remains on.

Choosing Between Genuine Honda, Fram, and Other Filters

A genuine Honda filter offers the reassurance of an OEM catalogue match when you have confirmed the correct application. Aftermarket filters can also be appropriate when they are listed specifically for your Accord’s engine. The useful comparison is not simply brand versus brand; it is whether the part is correctly catalogued, undamaged, and fitted properly.

Retail catalogues provide a wide range of oil-filter choices, including Genuine Honda options, for the 2010 Accord. Before choosing on price alone, use the 2010 Honda Accord filter catalogue to compare the application details available for your vehicle. Keep the receipt and packaging until you have confirmed that the filter fits and there are no leaks.

For most owners, the practical answer is simple: buy a correctly listed spin-on filter, verify the engine application before fitting it, and replace it whenever you carry out the engine-oil service. That avoids the confusion caused by relying on a similar-looking filter or an unverified cross-reference.

---